Versions Compared

Old Version 2

changes.mady.by.user Rachel Stefania Vroman

Saved on

compared with

New Version Current

changes.mady.by.user Caleb Marhoover

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Image RemovedImage AddedImage AddedImage AddedImage AddedImage Added


Info
titleConsiderations for this method
Pros

PROS:

  • Convenient
  • Able to produce wide variety of geometries
Cons:
  • Expensive
  • High degree of transparency best achieved through hand polishing
  • Some faces of parts require support material, so glossy finish from printer may be inconsistent, depending on part geometry.

 

Hand polishing is required to achieve high degree of transparency. Polishing may not be suitable for highly detailed geometric features.

Panel
titleOn this page

Table of Contents
maxLevel2

  • Very rigid and durable
  • High transparency/clarity (when polished)
  • Can be used in a multi-material print

CONS:

  • High cost
  • Achieving high clarity requires multi-step polishing and finishing process
  • Hue changes with exposure to UV light
  • Non-planar or small surfaces are difficult to polish

 


Material options

Or, use the drape command to create a NURBS surface from the topography mesh,
  • Then use the buildings to make holes in the new NURBS surface,
  • And use the new NURBS surface to trim away the subterranean parts of the buildings.
    • Then contour it all together. By trimming the surfaces, you avoid having to trim the contours as in option (i).
    Image Removed
    For keeping a clean edge, it helps to add rods for threading the layers.
  • For a large model as this one (4) square 3/16" dowel rods will work. Bass wood would work great but consider plexi rods for the areas with water.
    • Space holes for them evenly along the long side of the model, cutting through all of the contours. 
    Image Removed
    For this model, we're going to add plexi for the areas that have water by nesting it between every other layer of the primary material.The plexi layers should also include cutouts for rods.
    Image Removed
    The in-between layers should have a reveal in the areas where they meet water for a stronger visual effect.
    Image Removed
  • Lay out each layer on laser bed-sized (18" x 32") sheets of material. 
    1. One for water to be cut on plexi 
    2. The rest on primary material sheets. Since the layers are being stacked, it doesn't matter which side they are cut on so you can flip and rotate layers in order to minimize material waste. 
      Image Removed 

    • Making the model  

  • Prepare material for the number of sheets you will need to laser cut. 
    1. If buying material from the GSD Store, it will already be cut to the laser bed size.
    2. If buying material from other vendors, you most likely will need to cut material to the laser bed size (18" x 32").
  • Always test cut a small piece first to make sure that the laser is cutting the material through all the way. The edges of the cut sheets will be very visible, so use as low of a PPI setting as possible to minimize burning. 
    • Once all sheets have been cut:
  • Stack layers in order, by threading each layer onto the rods. 
    • A small amount of glue (Tacky or Sobo) will help hold the layers together.
    Image Removed 
     Glue the plexi layers to the primary material using epoxy or super glue 
    Image RemovedCut off any remaining length from the end of the rods so that they end flush with the material
    Filter by label (Content by label)showLabelsfalsemax5spacesfabricationlabshowSpacefalsesortmodifiedreversetruetypepagecqllabel = "kb-how-to-article" and type = "page" and space = "fabricationlab"labelskb-how-to-article
    TIME: assembly (hrImage Removed
     METHODMATERIALCOST ($/cubic ft)TIME: fab (hr)inch)TIME: totalMATERIAL RECYCLABILITY
    Image RemovedGlossy setting, Polished

    Vero Clear

    		$5.510.536.5no
    Production StepsTime requiredSpecial Equipment NeededConditionsAble to be colored?health and safetyChemical CompositionPPEWhere to Purchase

    Image Added

    		Glossy setting, UnpolishedPolished

    Vero Clear

    		$5.510.536.5no

    Fabrication Process

    You'll need a file with vertical contour lines at a horizontal spacing that matches the thickness of your modeling material. Use the "contour" Rhino command to generate them from NURBS surfaces or meshes of the topography and buildings.If your base file does not have a surface or mesh representing the topography, you can use the RhinoTerrain plugin (available in the Software folder on Goliath) to make a 3D mesh from horizontal topography lines.
    Image Removed
    You can either:Contour the mesh and the buildings together,Then clean up the resulting contour curves (delete building contours which are below the surface of the topography, and remove topography curves which are inside buildings).
    Image Removed
     
    $19.85 (plus cost of sandpaper and polishing media)Sample cube required 2 hours print time (plus 2 hours hand-polish time). Upload STL to 3D printing queue, requesting Vero Clear material and glossy setting.
    Remove support material and perform additional wet polish to faces as needed.

    Print time depends on volume and height of part, as well as other jobs in the print queue.


    		Objet Connex 3D PrinterExposing printed part to strong sources of light may change the hue and transparency of the part.Yes.
    At GSD can tint with Vero White or Agilus Black. Other colors possible elsewhere.    		Considered a hazardous substance in liquid form: toxic to aquatic life with long lasting effects, can cause serious eye damage or irritation, can cause skin sensitization; for other hazards, consult SDS. At least one constituant chemical is considered to be carcinogenic and possibly mutagenic.
    When used as described, the hazardous liquid is released from a cartridge only inside a printing system, so exposure is limited. Once cured, part is considered to be non-irritating and not sensitizing to skin. No other data available.    		Too many to list, see SDS: section 3Wear impervious gloves, tight sealing safety goggles, long-sleeved clothing.Fabrication Lab: 3D printing online queue

    Image Added

    		Glossy setting, Unpolished

    Vero Clear

    		$19.85Sample cube required 2 hours.Upload STL to 3D printing queue, requesting Vero Clear material and glossy setting.
    Remove support material.     		Print time depends on volume and height of part, as well as other jobs in the print queue.


    Fabrication Process


    Polishing


    Page Properties
    hiddentrue


    Related issues