Versions Compared

Old Version 3

changes.mady.by.user Rachel Vroman

Saved on

compared with

New Version Current

changes.mady.by.user Caleb Marhoover

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Image RemovedImage AddedImage AddedImage AddedImage AddedImage Added


Info
titleConsiderations for this method

ProsPROS:

  • Food Safe
  • Tear-resistant
  • Resilient once cured
  • Can be tinted colors colored with special pigments

Cons:

Special equipment needed (scale and vacuum chamber).

CONS:

  • Incompatible with some materials (chemically inhibiting the curing process is chemically inhibited)
Panel
titleOn this page

Table of Contents
maxLevel2

  • Requires degassing in vacuum chamber for maximum clarity
  • Mixture ratio 10:1 must be carefully measured

 


Material options

TIME: assembly (hrWith
 METHODMATERIALCOST ($/cubic inch)TIME: file prep (hr)TIME: fab (hr))TIME: totalMATERIAL RECYCLABILITY
Image RemovedWithout Vacuum ChamberSORTA-Clear 40$30851023no
Image RemovedProduction StepsTime requiredSpecial Equipment NeededConditionsAble to be colored?health and safetyChemical CompositionPPEWhere to Purchase

Image Added

Without Vacuum ChamberSORTA-Clear 40$62851023no

 

 

File preparation

You'll need a file with horizontal contour lines at a vertical spacing that matches the thickness of your modeling material.
If your base file contains contours at a different resolution, use the RhinoTerrain plugin (available in the Software folder on Goliath) to make a 3D mesh from the given contours.
Image Removed
You can either:Contour the mesh and the buildings together,Then clean up the resulting contour curves (delete building contours which are below the surface of the topography, and remove topography curves which are inside buildings).
Image Removed
Or, use the drape command to create a NURBS surface from the topography mesh,
  • Then use the buildings to make holes in the new NURBS surface,
  • And use the new NURBS surface to trim away the subterranean parts of the buildings.
    • Then contour it all together. By trimming the surfaces, you avoid having to trim the contours as in option (i).
    Put the resulting contours on your CUT layer, then copy them up (along the positive Z axis) one level. Put the copies on your ETCH layer.
    Image Removed
    Lay out each layer pair (one CUT, one ETCH) on laser bed-sized (18" x 32") sheets of material. Small layers can be nested inside larger ones to save material.
    Image Removed
     
    1. Label your sheets to keep track of stacking order. 

    Making the model

    1. Prepare material for the number of sheets you will need to laser cut. 
      1. If buying material from the GSD Store, it will already be cut to the laser bed size.
      2. If buying material from other vendors, you most likely will need to cut material to the laser bed size (18" x 32").
    2. Always test cut a small piece first to make sure that the laser is cutting the material through all the way. The edges of the cut sheets will be very visible, so use as low of a PPI setting as possible to minimize burning. 
    3. Once all sheets have been cut:
      1. Stack layers in order, aligning the top layer to the ETCH of the bottom layer.
      2. Glue layers together 
        1. Spray mount adhesive works best for fast assembly.
        2. Only spray on the bottom (non-visible) side of each layer to avoid messy craftsmanship.   

     

    Filter by label (Content by label)
    showLabelsfalse
    max5
    spacesfabricationlab
    showSpacefalse
    sortmodified
    reversetrue
    typepage
    cqllabel = "kb-how-to-article" and type = "page" and space = "fabricationlab"
    labelskb-how-to-article

    Page Properties
    hiddentrue
    Related issues 
    $0.8016.5 hours (30 minutes preparation and 16 hours cure time)Measure each component of the 2-part product into mixing container as specified by manufacturer's instructions.
    Stir thoroughly to combine two components.

    Pour into the lowest point of the model/mold to avoid trapping air bubbles. A thin stream poured slowly from high above may help to remove small air bubbles not collapsed by vacuum chamber.
    Allow 16 hours for substance to cure before handling.    		Pot life is 60 minutes. Cure time is 16 hours, regardless of volume. Curing can be accelerated by applying mild heat (up to 60º C). PRODUCT WILL DARKEN CONSIDERABLY IF HEATED.Scale to measure the two components by weight accurately.
    Large, clean mixing container and stir stick.

    		Product is a platinum-cure silicone rubber, and is incompatible with materials bearing platinum-cure inhibitors. Will not cure if ratio of two components is not accurately measured.Yes.
    Add a small amount of Silc Pig™ color pigment to Part A and mix thoroughly before combining with Part B.    		Part A: No data on possible toxicological effects available.
    Part B: No data on possible toxicological effects available.    		UnlistedVinyl gloves to limit skin contact, splash goggles to prevent contact with eye.
    (latex gloves will inhibit cure of the product)    		Reynolds Advanced Materials

    Image Added

    		With Vacuum ChamberSORTA-Clear 4017 hours (1 hour preparation and 16 hours cure time)

    See above, after measuring and mixing the two components, degas the mixture using a vacuum chamber. (Mixing container must be at least 4 times the volume of the combined components, as the gas expands and may over-flow the container.)

    Then follow remaining steps, above.

    		In addition to above, a vacuum chamber to degas the mixed substance before it is poured into mold/model.

     

     

    Mold preparation